# Tire Wear

**URL:** <https://community.electricforum.com/t/tire-wear/6178>\
**Category:** GEM Forum\
**Created:** [July 3, 2016, 7:41pm UTC](https://community.electricforum.com/t/tire-wear/6178 "2016-07-03T19:41:10Z")\
**Posts on this page:** 5\
**Page:** 2

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [December 15, 2019, 4:42pm UTC](https://community.electricforum.com/t/tire-wear/6178/21 "2019-12-15T16:42:40Z")

</div>

1 cut a piece of 2X4 24 inches long.

2 place it against the tire leaning out ward so it contacts the tire above the bulge

3 put a mark on the concrete at the front and back of the tire diameter

4 repeat on the other side

5 roll the cart back and measure the distance

6 adjust the toe to 1/8 toe in

1 full turn on each tie rod moves toe about 1/8 inch.

NOTE: MOST NEGATIVE CAMBER IS A RESULT OF EXCESSIVE TOE OUT. SHIMMING SHOULD NOT BE DONE BEFORE ADJUSTING TOE,

IF YOU SHIM TOE MUST MUST MUST BE ADJUSTED,

In a message dated 12/15/2019 10:34:21 AM Eastern Standard Time, [electricforum@discoursemail.com](mailto:electricforum@discoursemail.com) writes:

---

<div class="post-metadata">

**Author:** ![Craigs5711](https://avatars.discourse-cdn.com/v4/letter/c/48db29/32.png) [@Craigs5711](https://community.electricforum.com/u/Craigs5711)\
**Post date:** [December 17, 2019, 2:41pm UTC](https://community.electricforum.com/t/tire-wear/6178/22 "2019-12-17T14:41:22Z")

</div>

Thank You. I will remove the shim and adjust the toe. If that doesn’t fix it , then I will shim the camber. Thanks again.

---

<div class="post-metadata">

**Author:** ![Craigs5711](https://avatars.discourse-cdn.com/v4/letter/c/48db29/32.png) [@Craigs5711](https://community.electricforum.com/u/Craigs5711)\
**Post date:** [December 22, 2019, 3:16pm UTC](https://community.electricforum.com/t/tire-wear/6178/23 "2019-12-22T15:16:28Z")

</div>

Thank You,  
It was the Toe adjustment… I put took the shims out and just did the alignment… Huge improvement. Thank You

---

<div class="post-metadata">

**Author:** ![IRBGEM](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/irbgem/32/4550_2.png) [@IRBGEM](https://community.electricforum.com/u/IRBGEM)\
**Post date:** [March 30, 2020, 6:12pm UTC](https://community.electricforum.com/t/tire-wear/6178/24 "2020-03-30T18:12:02Z")

</div>

@Old_Houseboater Replying to an old thread, but just used your instructions to set the camber. Tracks much better now. Thank you.

---

<div class="post-metadata">

**Author:** ![AlexAnderson](https://avatars.discourse-cdn.com/v4/letter/a/49beb7/32.png) [@AlexAnderson](https://community.electricforum.com/u/AlexAnderson)\
**Post date:** [April 3, 2020, 5:29pm UTC](https://community.electricforum.com/t/tire-wear/6178/25 "2020-04-03T17:29:10Z")

</div>

> [@Firemickey](#):
>
> Hi All,  
> Both of my front tires are wearing very uneven on my 2002 e825. The outside of the tire is wearing extremely fast compared to inside (see pic).  
> Has anyone ever experienced this and is there a way to fix it. I have front disc brakes and installed adjustable shocks.

Wheel alignment required. Anyway you should check it

[Previous page](https://community.electricforum.com/t/tire-wear/6178.md?page=1)
