# HiI  Need help on BMS / Charging

**URL:** <https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619>\
**Category:** Battery & Chargers\
**Created:** [January 14, 2021, 3:18pm UTC](https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619 "2021-01-14T15:18:46Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![kh250](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/kh250/32/7787_2.png) [@kh250](https://community.electricforum.com/u/kh250)\
**Post date:** [January 14, 2021, 3:18pm UTC](https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619/1 "2021-01-14T15:18:46Z")

</div>

I am converting a classic bike to electric and have completed all the mechanical tasks. I am using a 48v DC motor 200 amp max run but this can be doubled for 14 seconds ( I might try the drag strip ). I will be building 4 battery packs. Each pack consists of 13 cells in series stacked 5 high with a copper bus bar at each end and 2 strips of 0.2mm pure nickel10mm strips to connect the 13 batteries (Samsung 407 35amp 4 amp hour )

I now need a BMS and on board charging ( 240v 13 amp supply as I am in the UK ) solution and detailed instructions on how to wire up. I wont be using the bike much at all once built but may well transfer the batteries to another project. I am not looking for a budget solution but don’t think I need top end .

Any advice on where to go / purchase would be much appreciated.

Thanks

Simon

---

<div class="post-metadata">

**Author:** ![Cblad](https://avatars.discourse-cdn.com/v4/letter/c/ecd19e/32.png) [@Cblad](https://community.electricforum.com/u/Cblad)\
**Post date:** [March 11, 2021, 3:37pm UTC](https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619/2 "2021-03-11T15:37:59Z")

</div>

hello,  
i’m in the same place as you. im converting a Golfcart, Toro Workman E2050 with S13 Samsung SDI cell and i’m use ZEVA BMS for it, but i have problem with program the charger Delta-Q 36v, i need the alorithms for it.

---

<div class="post-metadata">

**Author:** ![kh250](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/kh250/32/7787_2.png) [@kh250](https://community.electricforum.com/u/kh250)\
**Post date:** [March 11, 2021, 5:05pm UTC](https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619/3 "2021-03-11T17:05:20Z")

</div>

Hi  
I am using a Heyo BMS but have not installed it yet. I have had no response from the forum so have forgotten about it. I can only suggest you get a BMS from a company that is big / provides support or get on a Facebook page ( which I am going to try ) as there seem to be some friendly people on there .)

Good luck

Simon

---

<div class="post-metadata">

**Author:** ![jamesrule](https://avatars.discourse-cdn.com/v4/letter/j/c2a13f/32.png) [@jamesrule](https://community.electricforum.com/u/jamesrule)\
**Post date:** [September 7, 2022, 8:00am UTC](https://community.electricforum.com/t/hii-need-help-on-bms-charging/20619/4 "2022-09-07T08:00:32Z")

</div>

Hello, I juest purchased one [electric conversion kits](https://hovscoshop.com) for my bike ,but I dont kown how to install it.