# Gettig the half shaft out

**URL:** <https://community.electricforum.com/t/gettig-the-half-shaft-out/22730>\
**Category:** GEM Forum\
**Created:** [October 25, 2021, 11:31pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730 "2021-10-25T23:31:53Z")\
**Posts on this page:** 11\
**Page:** 1

<div class="post-metadata">

**Author:** ![TJC](https://avatars.discourse-cdn.com/v4/letter/t/54ee81/32.png) [@TJC](https://community.electricforum.com/u/TJC)\
**Post date:** [October 25, 2021, 11:31pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/1 "2021-10-25T23:31:53Z")

</div>

I am trying to get the half shaft away form the differential. The manual says it’s held on by a spring clip and to pry it away with two short pry bars, I don’t see anywhere I can get a pry bar between the cv joint and the differential. The only place there is a shoulder to pry against on the cv joint is too close to the differential to get anything but maybe a screwdriver in.

Any tips or ideas ?

Thanks in advance for any help.

---

<div class="post-metadata">

**Author:** ![JarJarJava](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/jarjarjava/32/15158_2.png) [@JarJarJava](https://community.electricforum.com/u/JarJarJava)\
**Post date:** [October 26, 2021, 12:05am UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/2 "2021-10-26T00:05:40Z")

</div>

Pair of heavy blade standard screwdrivers will work fine. So long your shaft isn’t all rusty, it should come pretty easily

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [October 26, 2021, 12:39am UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/3 "2021-10-26T00:39:45Z")

</div>

Yep - stick a big flat blade screwdriver in there and pry away from the diff, should pop right off, Make sure you have the wheel end out first, makes it much easier.

---

<div class="post-metadata">

**Author:** ![Derrick](https://avatars.discourse-cdn.com/v4/letter/d/d9b06d/32.png) [@Derrick](https://community.electricforum.com/u/Derrick)\
**Post date:** [October 26, 2021, 2:17am UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/4 "2021-10-26T02:17:35Z")

</div>

They can be a bit of a pain to get off, too much side (or vertical) pressure will cause it to bind. I fought with mine trying to get them off with pry bars and flat head screw drivers, and then they just slid off by hand when I tried to move them out of the way

---

<div class="post-metadata">

**Author:** ![MaxAtMaxMarine](https://avatars.discourse-cdn.com/v4/letter/m/90db22/32.png) [@MaxAtMaxMarine](https://community.electricforum.com/u/MaxAtMaxMarine)\
**Post date:** [October 27, 2021, 2:02am UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/5 "2021-10-27T02:02:22Z")

</div>

Had to use a pickle fork ball joint separator on mine - can be had from Harbor Freight, Advance, etc

---

<div class="post-metadata">

**Author:** ![TJC](https://avatars.discourse-cdn.com/v4/letter/t/54ee81/32.png) [@TJC](https://community.electricforum.com/u/TJC)\
**Post date:** [October 27, 2021, 3:25am UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/6 "2021-10-27T03:25:24Z")

</div>

SUCCESS !  
I got it apart this afternoon. Didn’t take much pressure, just an even effort form two large screwdrivers. I had sprayed the whole thing with penetrating oil the night before just for good measure.  
Thanks for all of the tips.

---

<div class="post-metadata">

**Author:** ![Reddevil](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/reddevil/32/6128_2.png) [@Reddevil](https://community.electricforum.com/u/Reddevil)\
**Post date:** [January 15, 2022, 9:02pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/7 "2022-01-15T21:02:41Z")

</div>

My question is how to get the inner joint to pop over the spring clip? Anyone have a trick?

With the good help of @JarJarJava i am putting the parts back on after our accident but this is not going together. Splines are fine, it will slip together without the clip. Is it time to face reality and accept I’m old and weak?

Any ideas appreciated.

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [January 15, 2022, 10:37pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/8 "2022-01-15T22:37:55Z")

</div>

@Reddevil - a little more explanation, please? Not really sure what you are describing.

If you mean putting the half shaft back on the gearbox output shaft? Just give it a wack with a rubber mallot. - don’t hit the rubber over the cv joint, you might split the rubber.

---

<div class="post-metadata">

**Author:** ![JarJarJava](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/jarjarjava/32/15158_2.png) [@JarJarJava](https://community.electricforum.com/u/JarJarJava)\
**Post date:** [January 15, 2022, 10:39pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/9 "2022-01-15T22:39:18Z")

</div>

It should just compress the circlip as it slides over. Is the groove over packed with grease or debris that might be preventing it from being compressed?

Also, just for shits and giggles, did you happen to try the other half shaft? With the damaged rubber boot?

That’s all I got… It really shouldn’t be this difficult.

---

<div class="post-metadata">

**Author:** ![TJC](https://avatars.discourse-cdn.com/v4/letter/t/54ee81/32.png) [@TJC](https://community.electricforum.com/u/TJC)\
**Post date:** [January 15, 2022, 10:47pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/10 "2022-01-15T22:47:37Z")

</div>

Mine slid right on with some even pressure.

---

<div class="post-metadata">

**Author:** ![Reddevil](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/reddevil/32/6128_2.png) [@Reddevil](https://community.electricforum.com/u/Reddevil)\
**Post date:** [January 15, 2022, 11:08pm UTC](https://community.electricforum.com/t/gettig-the-half-shaft-out/22730/11 "2022-01-15T23:08:37Z")

</div>

Thanks guys. Went in, had lunch and came back with my son who wrestled it on. Youth and vigor won the day.
