# Gem LSV wont move

**URL:** <https://community.electricforum.com/t/gem-lsv-wont-move/12446>\
**Category:** GEM Forum\
**Created:** [June 8, 2017, 7:39pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446 "2017-06-08T19:39:28Z")\
**Posts on this page:** 8\
**Page:** 1

<div class="post-metadata">

**Author:** ![pouledeau](https://avatars.discourse-cdn.com/v4/letter/p/b9e5f3/32.png) [@pouledeau](https://community.electricforum.com/u/pouledeau)\
**Post date:** [June 8, 2017, 7:39pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/1 "2017-06-08T19:39:28Z")

</div>

have 72 + V at solenoid, but -0- at controller ? Solenoid checks ok… What am i missing ?

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [June 8, 2017, 7:43pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/2 "2017-06-08T19:43:13Z")

</div>

Need more information.  
Year or controller type?  
Charger?  
B+ at controller is -0- ?  
What about pin 1 and 2 ?  
Solenoid won’t pull in if there is a charger interlock problem.  
If DQ charger look for B+ on green wire.

---

<div class="post-metadata">

**Author:** ![pouledeau](https://avatars.discourse-cdn.com/v4/letter/p/b9e5f3/32.png) [@pouledeau](https://community.electricforum.com/u/pouledeau)\
**Post date:** [June 8, 2017, 8:28pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/3 "2017-06-08T20:28:26Z")

</div>

GEM eS MODEL 2013 CHARGER IS DELTA Q NO POWER COMING TO CONTROLLER FROM SOLENOID…

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [June 8, 2017, 8:52pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/4 "2017-06-08T20:52:54Z")

</div>

The controller need B+ to pin 1 & 2 at a minimum to pull in solenoid.  
Check for B+ on green wire from charger. That is what allows car to run. (interlock)  
Any other faults should set an error code.

---

<div class="post-metadata">

**Author:** ![pouledeau](https://avatars.discourse-cdn.com/v4/letter/p/b9e5f3/32.png) [@pouledeau](https://community.electricforum.com/u/pouledeau)\
**Post date:** [June 8, 2017, 9:06pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/5 "2017-06-08T21:06:06Z")

</div>

HAVE ERROR CODE 51…RE-SET MASTER SWITCH ( 15 MIN OFF-THEN ON ) STILL NOTHING…TROUBLE SHOOT GUIDE SAYS TO REPLACE CONTROLLER !!

Robert Doucet  
H & H Golf Carts Inc.  
115 W. Harrison Ave.  
Harlingen, TX 78551  
956-423-3500 ( O ) 956-454-4323 ( C )

> **[H&H Golf Carts & Power Equipment](http://hhgolfcarts.com/)**
>
> We offer a wide selection of golf carts and power equipment, including Husqvarna, Maruyama, Toro, and more. We service and customize golf carts and repair power equipment. Check out our selection of Traeger Wood Fired Grills, accessories and...

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [June 8, 2017, 10:44pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/6 "2017-06-08T22:44:07Z")

</div>

Ge manual says low voltage in controller when key is turned on. Check control fuse.  
Might also re-seat 23 pin plug and check for B+ on 1 & 2.  
Pin 1 and or pin 2 need to precharge for contactor to pull in.  
I think it’s to prevent full power from reaching controller if something is shorted.

---

<div class="post-metadata">

**Author:** ![pouledeau](https://avatars.discourse-cdn.com/v4/letter/p/b9e5f3/32.png) [@pouledeau](https://community.electricforum.com/u/pouledeau)\
**Post date:** [June 9, 2017, 4:25pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/7 "2017-06-09T16:25:53Z")

</div>

…NOT SURE I UNDERSTAND…FLOW OF ELECTRICITY IS TO SOLENOID (CONTACTOR) PRIOR TO ACTIVATING CONTROLLER…HAVE NO POWER COMING FROM ONE SIDE OF CONTACTOR ( GOING TO CONTROLLER ) WOULD HAVE TO ASSUME THE CONTACTOR IS FAULTY, NO ? TROUBLESHOOTING SAYS JUST PUT NEW CONTROLLER…$$$

Robert Doucet  
H & H Golf Carts Inc.  
115 W. Harrison Ave.  
Harlingen, TX 78551  
956-423-3500 ( O ) 956-454-4323 ( C )

> **[H&H Golf Carts & Power Equipment](http://hhgolfcarts.com/)**
>
> We offer a wide selection of golf carts and power equipment, including Husqvarna, Maruyama, Toro, and more. We service and customize golf carts and repair power equipment. Check out our selection of Traeger Wood Fired Grills, accessories and...

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [June 9, 2017, 4:39pm UTC](https://community.electricforum.com/t/gem-lsv-wont-move/12446/8 "2017-06-09T16:39:19Z")

</div>

Contactor does NOT pull in, correct?  
The controller connects the coil to B- to pull it in.  
The other side of coil is B+.  
If you measure +72v on both sides of coil. Controller is not telling contactor it’s safe to pull in.  
The most basic condition needed is main --\> B- and +72v on pin 1 and 2.  
May very well be the controller.
