# FUSE #9 keeps blowing

**URL:** <https://community.electricforum.com/t/fuse-9-keeps-blowing/26342>\
**Category:** GEM Forum\
**Created:** [May 9, 2023, 2:15am UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342 "2023-05-09T02:15:42Z")\
**Posts on this page:** 12\
**Page:** 6

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [January 6, 2026, 9:40pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/101 "2026-01-06T21:40:18Z")

</div>

Ok, then leave the controller floating(not mounted), and remove the F1 and F2 wires off the top of the controller. (These are easy. They just pull off)

If still present,  
Then go for the A1 then the A2. Carefully isolate the cables so they dont spring off in a direction and ground out when testing.

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 9:46pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/102 "2026-01-06T21:46:40Z")

</div>

From previous

When unplugged the 2 wires from the motor the voltage dropped to around 2v more or less.

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [January 6, 2026, 9:56pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/103 "2026-01-06T21:56:09Z")

</div>

That instruction was for the 2 wire motor temp sensor. It has a plug down on the end of motor. (not to be confused with the Speed sensor which has the 3 wire plug.

Was this not correct?

Today I was talking about the F1 and F2 wires. they have their own wires/plugs directly on top of the motor controller.

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 10:08pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/104 "2026-01-06T22:08:47Z")

</div>

> [@AssyRequired](#):
>
> That instruction was for the 2 wire motor temp sensor. It has a plug down on the end of motor. (not to be confused with the Speed sensor which has the 3 wire plug.

Correct when I unplugged the temp sensor the 2 (orange and black) wires from motor the voltage dropped significantly to 2v.

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [January 6, 2026, 10:20pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/105 "2026-01-06T22:20:46Z")

</div>

Now I want to unplug the Field Wires marked F1 and F2 off the top of the controller.

 ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/3X/6/d/6dc9e027f9cb34fda56efa5e039acf7db5111c2b.jpeg)

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 10:37pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/106 "2026-01-06T22:37:21Z")

</div>

> [@AssyRequired](#):
>
> Ok, then leave the controller floating(not mounted), and remove the F1 and F2 wires off the top of the controller. (These are easy. They just pull off)
> 
> If still present,  
> Then go for the A1 then the A2. Carefully isolate the cables so they dont spring off in a direction and ground out when testing.

When removed F1 & F2 voltage 72v still there.

Removed A1 first and voltage all over the place with a clicking sound.

Remove A1 & A2 voltage still there. Connect A1 and voltage all over the place with clicking sound.

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [January 6, 2026, 10:52pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/107 "2026-01-06T22:52:03Z")

</div>

Interesting. Faint clicking?  
Are any of your wires touching things they should not be?

Now that your Motor wires are disconnected from controller we can see if any of them are shorting to chassis.

Power off at MainSwitch (don’t need it).  
Switch your meter to Ohms.  
Place one meter probe on a clean spot on Chassis.  
Place the other meter probe on the cable formerly connected to A1.  
Do you get a reading? or OL on your meter?  
Do same for A2  
Do same for F1  
Do same for F2

Report back with findings.

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 10:58pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/108 "2026-01-06T22:58:58Z")

</div>

Still voltage of 78v

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [January 6, 2026, 11:04pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/109 "2026-01-06T23:04:44Z")

</div>

Ok. Go ahead and put your car back together and run it as it is.

If you aren’t even going to try and read my instructions, I have much better things to do.  
I’m out.

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 11:09pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/110 "2026-01-06T23:09:38Z")

</div>

My apologies didn’t see last message. Will follow directions.

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 11:32pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/111 "2026-01-06T23:32:11Z")

</div>

> [@AssyRequired](#):
>
> Place one meter probe on a clean spot on Chassis.  
> Place the other meter probe on the cable formerly connected to A1.  
> Do you get a reading? or OL on your meter?  
> Do same for A2  
> Do same for F1  
> Do same for F2

A1 23kOhm

A2 24kOhm

F1 & F2 OL

Thank you for patience

---

<div class="post-metadata">

**Author:** ![earami](https://avatars.discourse-cdn.com/v4/letter/e/ed8c4c/32.png) [@earami](https://community.electricforum.com/u/earami)\
**Post date:** [January 6, 2026, 11:33pm UTC](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342/112 "2026-01-06T23:33:40Z")

</div>

> [@AssyRequired](#):
>
> Interesting. Faint clicking?  
> Are any of your wires touching things they should not be?

Not touching anything

[Previous page](https://community.electricforum.com/t/fuse-9-keeps-blowing/26342.md?page=5)
