# COMPLETE list of GEM error CODES

**URL:** <https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492>\
**Category:** GEM Forum\
**Created:** [October 11, 2010, 11:05am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492 "2010-10-11T11:05:27Z")\
**Posts on this page:** 20\
**Page:** 2

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [April 11, 2014, 6:53pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/21 "2014-04-11T18:53:57Z")

</div>

More than likely, the motor speed sensor is bad, or the associated wiring has lost continuity. The speed sensor and its magnet are both Club Car Precedent parts and can be ordered from any golf car dealer. For the sensor order 1022656-01 and for the magnet order 1022657-01. Be sure that your charger is set for the actual battery type you are using.

Daniel

---

<div class="post-metadata">

**Author:** ![Dickydoo1](https://avatars.discourse-cdn.com/v4/letter/d/ea666f/32.png) [@Dickydoo1](https://community.electricforum.com/u/Dickydoo1)\
**Post date:** [April 19, 2014, 11:46am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/22 "2014-04-19T11:46:45Z")

</div>

Thanks for the listing. This will save me a lot of wasted time.

---

<div class="post-metadata">

**Author:** ![chadburu](https://avatars.discourse-cdn.com/v4/letter/c/278dde/32.png) [@chadburu](https://community.electricforum.com/u/chadburu)\
**Post date:** [April 20, 2014, 6:22pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/23 "2014-04-20T18:22:09Z")

</div>

Sorry if i’m posting this in the wrong area. Had trouble finding the right area. This is my gem issue. I have a code -51. This is the history. Last fall I got 3/6 batteries new prior three where 2 years old. I kept up on charging them all winter. One battery really would take much charge of the 3 that was 2 years old. I took it out and it didn’t have any pep. I assumed that that one battery was just bad so today I bought a new one for that poor battery. I installed it and now i’m getting a -51 code and it wont do anything. Any ideas?

Thanks!

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [April 21, 2014, 4:30pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/24 "2014-04-21T16:30:12Z")

</div>

Are you sure the -51 error came up immediately after replacing the battery? If so, check to be sure the battery is not connected backwards. Ignore the colors of the wires and confirm that the string of battery connections goes ±±±±± .

Daniel

---

<div class="post-metadata">

**Author:** ![chadburu](https://avatars.discourse-cdn.com/v4/letter/c/278dde/32.png) [@chadburu](https://community.electricforum.com/u/chadburu)\
**Post date:** [April 22, 2014, 3:35pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/25 "2014-04-22T15:35:37Z")

</div>

Doubled checked it…is correct…I checked all the fuses and they are good…volt metered the connection that is to the right of the solenoid on the right that has a fuse able link on it and it tested 72 volts…Sometimes 73…What should I check next?

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [April 24, 2014, 2:53pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/26 "2014-04-24T14:53:32Z")

</div>

Be sure that 72 volts is actually reaching your controller. Otherwise, substitute another like motor controller or have your controller tested.

Daniel

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [August 10, 2014, 8:59pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/27 "2014-08-10T20:59:17Z")

</div>

Check the motor speed sensor. I assume you are sing the yellow Delta-Q charger in this GEM. Did you change the charger’s setting when the batteries were replaced with a different type. GEL, AGM, and flooded all use different settings.

Daniel

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [August 10, 2014, 9:02pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/28 "2014-08-10T21:02:09Z")

</div>

Passed 24,000 hits on this thread tonight! Glad this information has helped a lot of people. Thanks to those who have helped me add new codes to this list.

Daniel

---

<div class="post-metadata">

**Author:** ![Jolly\_Rodgers](https://avatars.discourse-cdn.com/v4/letter/j/7bcc69/32.png) [@Jolly\_Rodgers](https://community.electricforum.com/u/Jolly_Rodgers)\
**Post date:** [October 6, 2014, 6:11am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/29 "2014-10-06T06:11:16Z")

</div>

Thank you Daniel for sharing all your knowledge.

I am working on a 2002 e825. I knew I was getting into a project when I bought it, since it did not work. I have had controller rebuilt by ride 4 fun and the charger upgraded and repaired by electric conversions. I installed both units yesterday and still have same problem.

When I turn on the main switch the BDI comes up with a 4 numbers like 9459 or something similar, then the display turns off and thats it. Looking at the service manual it says to check for voltage on pin 2 of controller plug. What is the voltage suppose to be? I read above where you said to check fuses. Is there a fuse for the BDI that I need to check and if so where would it be?  
I also have the same problem that is stated earlier in this thread that I get a buzzing sound when I put switch in road mode, no noise in turf. The buzz is coming from a round looking relay above the dc to dc convertor. Thanks in advance

---

<div class="post-metadata">

**Author:** ![Jolly\_Rodgers](https://avatars.discourse-cdn.com/v4/letter/j/7bcc69/32.png) [@Jolly\_Rodgers](https://community.electricforum.com/u/Jolly_Rodgers)\
**Post date:** [October 6, 2014, 6:13am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/30 "2014-10-06T06:13:16Z")

</div>

O h yeah I forgot to mention the contactor is not operating either. This cart is the devil!!

---

<div class="post-metadata">

**Author:** ![ppetty407](https://avatars.discourse-cdn.com/v4/letter/p/fbc32d/32.png) [@ppetty407](https://community.electricforum.com/u/ppetty407)\
**Post date:** [October 23, 2014, 7:08pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/31 "2014-10-23T19:08:27Z")

</div>

What is motor controller?

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [October 23, 2014, 10:46pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/32 "2014-10-23T22:46:10Z")

</div>

Not a problem I have seen before. Be sure all of the wiring connections are correct and tight. What is your battery voltage? Check the DC convertor to see that you have 12 volts at the fuses.

Daniel

---

<div class="post-metadata">

**Author:** ![DanVero](https://avatars.discourse-cdn.com/v4/letter/d/da6949/32.png) [@DanVero](https://community.electricforum.com/u/DanVero)\
**Post date:** [April 24, 2015, 5:26am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/33 "2015-04-24T05:26:19Z")

</div>

[I][B]06[/B] accelerator pedal closed safety lock out release pedal before  
selecting fwd or rev[/I]

What exactly does that mean? … Thanks for you help, Dan

---

<div class="post-metadata">

**Author:** ![Fairway](https://avatars.discourse-cdn.com/v4/letter/f/258eb7/32.png) [@Fairway](https://community.electricforum.com/u/Fairway)\
**Post date:** [April 26, 2015, 8:45am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/34 "2015-04-26T08:45:35Z")

</div>

What does the intermittent alarm mean that I get when I plug in the Zivan charger?

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [April 30, 2015, 7:07am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/35 "2015-04-30T07:07:19Z")

</div>

The -06 error indicates throttle was not released before selecting forward or reverse. This is to prevent vehicle runaway in the event of stuck switches, incorrect wiring, or a stuck throttle. The -11 code is similar in that it prevents vehicle runaway in the event the throttle is stuck or when the parking brake is left on. The most common example of these codes is when the floor mat gets stuck under the throttle.

Daniel

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [April 30, 2015, 7:09am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/36 "2015-04-30T07:09:08Z")

</div>

Please describe the intermittent alarm. What colors are displayed and what sound is there? What brand charger do you have?

Daniel

---

<div class="post-metadata">

**Author:** ![HappyK](https://avatars.discourse-cdn.com/v4/letter/h/8edcca/32.png) [@HappyK](https://community.electricforum.com/u/HappyK)\
**Post date:** [September 11, 2015, 9:47am UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/37 "2015-09-11T09:47:58Z")

</div>

> [@GEMmechanic;19536](#):
>
> First try opening and closing the master switch to reset the controller.

Hi GEMmechanic. I have ‘Error23’ coming up and my Citroen Evie is just creeping along. Please, would you have any idea where I should look for the master switch so I can try and reset the controller? Many thanks!

---

<div class="post-metadata">

**Author:** ![GEMmechanic](https://avatars.discourse-cdn.com/v4/letter/g/ecccb3/32.png) [@GEMmechanic](https://community.electricforum.com/u/GEMmechanic)\
**Post date:** [September 26, 2015, 6:30pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/38 "2015-09-26T18:30:22Z")

</div>

I am not familiar with this vehicle.

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [September 26, 2015, 7:04pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/39 "2015-09-26T19:04:00Z")

</div>

Google found this. No help on reset.

Vehicle 2009 Citroen C1 Ev’ie  
This is my Citroen C1 Ev’ie  
Motor AC-50 3-Phase AC  
Unknown Motor brand - but it is rated at 30kw  
Drivetrain 30kw AC Motor  
Controller Curtis 1238r  
Curtis AC controller upto 650 amp but limited to 320 amps.  
Batteries 25, 3.30 Volt, Lithium-Ion  
Thundersky Lithium-Ion Battery 25 cells & 160ah which give  
13.2kwh of stored energy  
System Voltage 83 Volts  
Charger Zivan NG3  
Zivan NG3 charger set for 96 volts and 18 amp output. The car  
has got a custom BMS that monitors and keeps the battery pack  
balanced and controls the charger.  
Heater Electric heater heats a small fluid reservoir and this in turn uses the  
existing heat exchanger. The heater draws 35 amps from the main battery pack ( 2.8 kw )  
DC/DC Converter   
HWZ1 13.6 volt 25 amp max  
Top Speed 65 MPH (104 KPH)  
The top speed is limited by the controller.  
Acceleration The car if fairly quick in getting from 0 - 30 mph and then slowly  
makes it way up to 60. I have had it at 65 mph.  
Range 60 Miles (96 Kilometers)  
It has a maximum range of 60 miles. When the car gets to 25%  
soc it limits the speed to 30mph. I have found this to be a realistic  
number for the range of the car.  
EV Miles   
Start: 6,514 Miles (10,481 Kilometers)  
Current: 13,320 Miles (21,431 Kilometers)  
Total: 6,806 Miles (10,950 Kilometers)  
Seating Capacity It will seat 4 adults in comfort.  
Curb Weight 1,900 Pounds (863 Kilograms)  
The curb weight of the vehicle is under 900kg

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [September 27, 2015, 1:18pm UTC](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492/40 "2015-09-27T13:18:45Z")

</div>

if you cannot find the switch just disconnect one of the battery cables.

[Previous page](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492.md?page=1)

[Next page](https://community.electricforum.com/t/complete-list-of-gem-error-codes/1492.md?page=3)
