# Code 81 strikes again!

**URL:** <https://community.electricforum.com/t/code-81-strikes-again/14359>\
**Category:** GEM Forum\
**Created:** [August 21, 2018, 1:54pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359 "2018-08-21T13:54:25Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![greengearhead](https://avatars.discourse-cdn.com/v4/letter/g/8e8cbc/32.png) [@greengearhead](https://community.electricforum.com/u/greengearhead)\
**Post date:** [August 21, 2018, 1:54pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359/1 "2018-08-21T13:54:25Z")

</div>

After reading up on this forum I am seeking advice mostly on where to buy a new speed sensor magnet. The magnet has a single crack and was found with a nice layer of magnetized grease chuncks stuck to it. Last pic shows my failed attempt to clean the magnet in hopes that it would start working. I did not think to glue the magnet down at the time. At this point I want to buy a new magnet if available.

 ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/9/9bf87b9862006cb899f60413462b37a56b1aeef0.jpeg)  
 ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/f/f44414457d892a5c5e472fefdeb2b65871fa2b30.jpeg) ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/e/e80586e069c68c602838e9d687212dedd3881e37.jpeg)

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [August 21, 2018, 2:30pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359/2 "2018-08-21T14:30:49Z")

</div>

Any GEM dealer, nev parts, some EZ GO dealers, Ebay.

---

<div class="post-metadata">

**Author:** ![Mr.Vern](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/mr.vern/32/2658_2.png) [@Mr.Vern](https://community.electricforum.com/u/Mr.Vern)\
**Post date:** [August 21, 2018, 3:19pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359/3 "2018-08-21T15:19:56Z")

</div>

This is the one I bought. Never installed it but it looks right. I can check the fitment on a motor later today if you need me to.

> **[Speed Sensor Motor Magnet For Club Car DS Precedent IQ With GE Motors | eBay](https://www.ebay.com/itm/Speed-Sensor-Motor-Magnet-For-Club-Car-DS-Precedent-IQ-With-GE-Motors/191563722630?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649)**
>
> This will only work on Club Cars DS & Precedent IQ with GE motors. Speed Sensor Magnet for GE Motors. 4 - Now you can gain access to the magnet. Simple remove the magnet by using a small flat head screwdriver or socket. | eBay!

---

<div class="post-metadata">

**Author:** ![Alex9a](https://avatars.discourse-cdn.com/v4/letter/a/d9b06d/32.png) [@Alex9a](https://community.electricforum.com/u/Alex9a)\
**Post date:** [August 21, 2018, 8:40pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359/4 "2018-08-21T20:40:13Z")

</div>

Over time, the magnetic ring is losing power. The hall sensor is not defective. You need to make your magnet. I made wheel from 5mm polycarbonate and 4 small neodymium magnets. It is important to understand how the polarity of the magnet triggered the sensor. And POXIPOL )))

 ![IMG_1275](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/9/9a29138da0bf584bde1840074d0829dc1f55d5b6.jpeg)

---

<div class="post-metadata">

**Author:** ![Alex9a](https://avatars.discourse-cdn.com/v4/letter/a/d9b06d/32.png) [@Alex9a](https://community.electricforum.com/u/Alex9a)\
**Post date:** [August 21, 2018, 9:21pm UTC](https://community.electricforum.com/t/code-81-strikes-again/14359/5 "2018-08-21T21:21:10Z")

</div>

As a temporary solution I did so. It hall sensor from old gazoline auto.  
There is only one subtlety. This sensor should be powered from 5 volts. If it is powered from the red wire in the regular hall sensor, it will give 12 volts to the motor controller. How he would react to this I don’t know. The simplest solution is to put before the new hall sensor to the red wire of the IC 78L05 or 7805.  
It is worth noting that I have a slightly different type of hall sensor.

 ![IMG_1247%20(2)](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/d/d50f08c3963ed2fd84b900b706e0c9416826654c.jpeg)
