# Brakes Rubbing

**URL:** <https://community.electricforum.com/t/brakes-rubbing/5946>\
**Category:** GEM Forum\
**Created:** [April 17, 2016, 6:55pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946 "2016-04-17T18:55:40Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Firemickey](https://avatars.discourse-cdn.com/v4/letter/f/c89c15/32.png) [@Firemickey](https://community.electricforum.com/u/Firemickey)\
**Post date:** [April 17, 2016, 6:55pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946/1 "2016-04-17T18:55:40Z")

</div>

Hi All,  
So I go to replace my of my rear wheel cylinders because it was leaking.  
Goes on with no issue and I bleed the new cylinder. Then I go to put the drums back on ( since I had it up I took off both drums to repaint them) they were really tight to get back on. I tried everything I could to get the brake shoes in but still a real tight fit. Now I have a rubbing sound in both sides.

What is the secret to get the shoes back in ???

Thanks…Tim

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [April 17, 2016, 7:09pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946/2 "2016-04-17T19:09:43Z")

</div>

Take a hammer an drive them back toward center. I take a large screw driver and pry them out then drive them back in 4 or 5 times to make sure their not frozen in the tension adjusters They will automatically reset themselves to the proper clearance after a few brake applications.

Rodney

---

<div class="post-metadata">

**Author:** ![Firemickey](https://avatars.discourse-cdn.com/v4/letter/f/c89c15/32.png) [@Firemickey](https://community.electricforum.com/u/Firemickey)\
**Post date:** [April 17, 2016, 7:19pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946/3 "2016-04-17T19:19:22Z")

</div>

Got it,

So use the screw driver to pry the shoe away from the back plate and a hammer to get them back in, should I use a fibber mallet or wood block so the hammer does not damage the brake lining or the hammer won’t damage it?

Thanks…Tim

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [April 17, 2016, 7:44pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946/4 "2016-04-17T19:44:36Z")

</div>

You DON’T pry away from the back plate.

You put the screwdriver down into the opening and pry the shoes outward toward the front/back of the car. THEN hammer them back in. Do it 4 or 5 times.

---

<div class="post-metadata">

**Author:** ![Firemickey](https://avatars.discourse-cdn.com/v4/letter/f/c89c15/32.png) [@Firemickey](https://community.electricforum.com/u/Firemickey)\
**Post date:** [April 24, 2016, 9:28pm UTC](https://community.electricforum.com/t/brakes-rubbing/5946/5 "2016-04-24T21:28:37Z")

</div>

Thanks OLD HOUSEBOATER that worked
