# 8KW Motor - Sevcon Controller - Digital Dash

**URL:** <https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438>\
**Category:** GEM Forum\
**Created:** [April 2, 2020, 12:44am UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438 "2020-04-02T00:44:30Z")\
**Posts on this page:** 20\
**Page:** 2

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [April 5, 2020, 11:21pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/21 "2020-04-05T23:21:10Z")

</div>

@Inwo  
Tory’s was really good, it would just cutoff at high RPM on a Size6, did not work well on a Size4. I may have loaded an old DCF file. Next time I go over and tune it I will send you the DCF.  
I changed the throttle to 12v as that what DVT was reading  
I changed the Encoder from 5 to 10v  
The Zone file is GREAT, but it is very “tame”, I wish we could set the AMPS to 550 from 350 - not that it really matters. The Zone is designed for a Size 4, but should work fine in the Size 6.

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [April 5, 2020, 11:27pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/22 "2020-04-05T23:27:57Z")

</div>

I’m quite sure we can boost the performance of the zone in a s6. With 17:1 My e2 is perfect. I wouldn’t notice more power. It’s on the edge of spinning tires now. I can test in the anvil, as that only runs 45 with the zone.  
If troy works fine it’s easier for me to run that than monkey with the zone.

---

<div class="post-metadata">

**Author:** ![Troyin909](https://avatars.discourse-cdn.com/v4/letter/t/57b2e6/32.png) [@Troyin909](https://community.electricforum.com/u/Troyin909)\
**Post date:** [April 9, 2020, 10:15pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/23 "2020-04-09T22:15:47Z")

</div>

Mike told me to change the voltage at some point in my setup but I’ve been working on stuff around the house, so I still need to give it a shot cause my setup will error out once you get to a certain rpm and voltage. I believe I’m set at 7600 rpms which gets me 43mph every time. But of course I’m aiming for the 50 + mph. Then I’m good. 😂

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [April 10, 2020, 2:18am UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/24 "2020-04-10T02:18:54Z")

</div>

You sure it’s over voltage? We’ve been running 9k rpm.  
Set encoder voltage to 10v and keep encoder wires short and away from power cables. Previous to that I would get encoder errors.  
I asked R4F to look for 6:1 gears again. I still think the Pmac is a winner with tall enough gears to run 4k rpm.  
Maybe 1:1. Direct to wheels.🤔😉🤣

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [April 10, 2020, 2:52am UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/25 "2020-04-10T02:52:01Z")

</div>

Yep. Encoder is what I sent him the instructions for. He just needs to test it.

🙂

---

<div class="post-metadata">

**Author:** ![Troyin909](https://avatars.discourse-cdn.com/v4/letter/t/57b2e6/32.png) [@Troyin909](https://community.electricforum.com/u/Troyin909)\
**Post date:** [April 11, 2020, 4:10pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/26 "2020-04-11T16:10:47Z")

</div>

I had to watch this again and think? Dang this guy is good! Give credit where credit is due. I love it!

---

<div class="post-metadata">

**Author:** ![JarJarJava](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/jarjarjava/32/15158_2.png) [@JarJarJava](https://community.electricforum.com/u/JarJarJava)\
**Post date:** [April 28, 2020, 5:24pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/27 "2020-04-28T17:24:17Z")

</div>

Mike, question…

will this work with an old android phone (Samsung J3) or does it need a more modern tablet?

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [April 28, 2020, 5:35pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/28 "2020-04-28T17:35:54Z")

</div>

It just runs the Torque Pro app, so if you can download and run that app on your phone you are golden.

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 19, 2020, 1:48pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/29 "2020-06-19T13:48:57Z")

</div>

I missed this post. Thanks for pointing me to it. Very cool. I already run Torque in my truck so the learning curve on this will be very low. I went ahead and grabbed a Can Translator too.

---

<div class="post-metadata">

**Author:** ![Troyin909](https://avatars.discourse-cdn.com/v4/letter/t/57b2e6/32.png) [@Troyin909](https://community.electricforum.com/u/Troyin909)\
**Post date:** [June 20, 2020, 6:41pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/30 "2020-06-20T18:41:16Z")

</div>

Man that’s really nice I’d say I like it but I really LOVE IT!! Lol

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 27, 2020, 6:04pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/31 "2020-06-27T18:04:14Z")

</div>

Do you have an example of how to add the custom PIDs? I got stuck on the last two.

Pid=dd05  
NAme=rpm  
Short name=rpm  
Min/max  
Unit type=?  
Equation=?

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [June 27, 2020, 6:33pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/32 "2020-06-27T18:33:10Z")

</div>

Yep. As soon as I get back to my computer I will post it.

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [June 27, 2020, 6:49pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/33 "2020-06-27T18:49:09Z")

</div>

Here is the cvs file - should have all the info you need. I had to play around with the name and display name to get them the way I wanted on the Dashboard, but the formulas and addresses should all be correct.

[Sevcon+PID-mdn.csv](https://community.electricforum.com/uploads/short-url/g38dhRDvpF1B1XRM5cdZJjgKtai.csv) (706 Bytes)

@diymatt - did you get the info?

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 28, 2020, 12:39am UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/34 "2020-06-28T00:39:11Z")

</div>

I did. Thank you.

It didn’t work for me so I’ll revisit this tomorrow.

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 28, 2020, 11:29am UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/35 "2020-06-28T11:29:59Z")

</div>

My tablet connects to the OBD2 dongle. I can see it communicating. I entered the PIDs manually instead of doing the csv import. Maybe that has something to do with it. I’ll give that a try sometime today.

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [June 28, 2020, 2:26pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/36 "2020-06-28T14:26:17Z")

</div>

I never tried an import, I just entered them manually, the file came from Thuderstruck and I made some modifications so I may have deleted a comma or something.

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 28, 2020, 7:32pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/37 "2020-06-28T19:32:19Z")

</div>

Why is everything fighting me.

 ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/3/3e6b3a3927a0c93f8767d4fb32130e43ff4baa4a.jpeg)

Top left shows Ecu is connected.  
In the background there is the obd2 dongle. It flashes green with connectivity.

 ![image](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/4/4a3a50d1b16eedae161ab35cf4eee498e7dc2ebf.jpeg)

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 28, 2020, 8:05pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/38 "2020-06-28T20:05:21Z")

</div>

I grabbed the pro version and things are going better. The lite version doesn’t seem to pull in the custom PIDs or I was just doing something wrong.

---

<div class="post-metadata">

**Author:** ![MikeKC](https://avatars.discourse-cdn.com/v4/letter/m/90ced4/32.png) [@MikeKC](https://community.electricforum.com/u/MikeKC)\
**Post date:** [June 28, 2020, 8:13pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/39 "2020-06-28T20:13:26Z")

</div>

Oh, yes you have to have the PRO version - sorry if that was not clear.

---

<div class="post-metadata">

**Author:** ![diymatt](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/diymatt/32/1822_2.png) [@diymatt](https://community.electricforum.com/u/diymatt)\
**Post date:** [June 28, 2020, 8:47pm UTC](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438/40 "2020-06-28T20:47:52Z")

</div>

Ok, all good in the hood now.

The connection seems spotty but that might be my crappy Bluetooth dongle I suppose.

[![](https://img.youtube.com/vi/AAVzS1e0i2g/maxresdefault.jpg "June 28, 2020") ](https://www.youtube.com/watch?v=AAVzS1e0i2g)

[Previous page](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438.md?page=1)

[Next page](https://community.electricforum.com/t/8kw-motor-sevcon-controller-digital-dash/18438.md?page=3)
