# 48v trans 2 battery installation

**URL:** <https://community.electricforum.com/t/48v-trans-2-battery-installation/12054>\
**Category:** GEM Forum\
**Created:** [February 13, 2017, 3:58am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054 "2017-02-13T03:58:18Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 3:58am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/1 "2017-02-13T03:58:18Z")

</div>

I have a 48v trans 2 car. I got it without batterys and they didnt know how they hooked back up. I got 4 12v batterys i am going to use to test before i get 6 8v batteries. I know about the range with the 12v i just want to test it before spending money on non returnable 8v batteries. If anyone knows how to hook the batteries up i would highly appreciate it thank you

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [February 13, 2017, 4:13am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/2 "2017-02-13T04:13:25Z")

</div>

Should be just two big cables for B+ and B-.  
Then possibly two from charger. And two smaller B+ and B- to control circuits .

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 4:26am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/3 "2017-02-13T04:26:15Z")

</div>

Well i tested the motor and it spins when i hooked the jumper to it. But not sure if any other electrical is any good

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 4:49am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/4 "2017-02-13T04:49:15Z")

</div>

The link you put in. the one who posted it couldnt add the link in because it was too big and he hasnt been on that site sense 2012. There wasnt a link to it were to find it either

---

<div class="post-metadata">

**Author:** ![Gem\_e2](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/gem_e2/32/1849_2.png) [@Gem\_e2](https://community.electricforum.com/u/Gem_e2)\
**Post date:** [February 13, 2017, 5:27pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/5 "2017-02-13T17:27:35Z")

</div>

Look if this will help

 ![](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/1X/4bda8b24c14dc49b9d690433c91d1aae9ada9ba1.png)

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 5:35pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/6 "2017-02-13T17:35:08Z")

</div>

I think you have found it ill go try thi right now. Thanks alot

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 6:19pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/7 "2017-02-13T18:19:58Z")

</div>

Im pretty sure thats the right way to hook up the batterys but the cart is just beeping really loud. But the horn and blinkers and lights work

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [February 13, 2017, 7:01pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/8 "2017-02-13T19:01:38Z")

</div>

It is beeping because the E brake handle is in the down position with the key off

---

<div class="post-metadata">

**Author:** ![Gem\_e2](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/gem_e2/32/1849_2.png) [@Gem\_e2](https://community.electricforum.com/u/Gem_e2)\
**Post date:** [February 13, 2017, 7:04pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/9 "2017-02-13T19:04:55Z")

</div>

Hi  
ok have not see none of that 48v carts  
yes maybe the brake or reverse alarm beeper ?

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 8:38pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/10 "2017-02-13T20:38:22Z")

</div>

Why isnt the cart moving with all the batterys connected

---

<div class="post-metadata">

**Author:** ![Gem\_e2](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/gem_e2/32/1849_2.png) [@Gem\_e2](https://community.electricforum.com/u/Gem_e2)\
**Post date:** [February 13, 2017, 9:24pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/11 "2017-02-13T21:24:23Z")

</div>

is it totally dead ?  
did beeper stop ?  
can you here solenoid click ?

do you have charger connected ?

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 9:59pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/12 "2017-02-13T21:59:09Z")

</div>

All batteries are fully charged. One of the beepers stoped, and yes it makes a clicking noise

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [February 13, 2017, 10:04pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/13 "2017-02-13T22:04:34Z")

</div>

Could be a lot of reasons.

First things first What Model controller do you have?

[http://www.fsip.biz/GEManualsDownload.html](http://www.fsip.biz/GEManualsDownload.html)

Check the above site for your controller. There is a trouble shooting guide in the manual.for your cart.

Start at the top and go thru the steps.

If the solenoid clicks when you press the throttle check to see if your getting any output voltage to the motor. If you are you probably have motor problems. If not you could have a defective controller. Try both forward and reverse.

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [February 13, 2017, 10:21pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/14 "2017-02-13T22:21:42Z")

</div>

Does that car display error codes?

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 13, 2017, 11:14pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/15 "2017-02-13T23:14:20Z")

</div>

No it doesn’t display error codes. I think its a key switch issue could i “hot wire” it some how

---

<div class="post-metadata">

**Author:** ![Gem\_e2](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/gem_e2/32/1849_2.png) [@Gem\_e2](https://community.electricforum.com/u/Gem_e2)\
**Post date:** [February 14, 2017, 7:40pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/16 "2017-02-14T19:40:00Z")

</div>

Hi  
dont know what controller you have

but if old 48v Curtis you can try and hot wire it here on pin 1  
or check voltage with meter

 ![](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/1X/d0c34d4abbda715e4eb691e1a34ac8f8516b0ac7.png)

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [February 14, 2017, 8:28pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/17 "2017-02-14T20:28:44Z")

</div>

> [@Gem\_e2](#):
>
> ok have not see none of that 48v carts

GEM uses GE controller

I have a TRANS 2 wiring diagram that should be close

email me [rodneyadiehl@aol.com](mailto:rodneyadiehl@aol.com)

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 15, 2017, 12:35am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/18 "2017-02-15T00:35:35Z")

</div>

Yeah i looked at the controller and it is a curtis do i just un plug the wire to the pin # 1

---

<div class="post-metadata">

**Author:** ![Johnny240](https://avatars.discourse-cdn.com/v4/letter/j/2bfe46/32.png) [@Johnny240](https://community.electricforum.com/u/Johnny240)\
**Post date:** [February 15, 2017, 3:04am UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/19 "2017-02-15T03:04:01Z")

</div>

Thanks for finding it. I e-mailed you

---

<div class="post-metadata">

**Author:** ![Gem\_e2](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/gem_e2/32/1849_2.png) [@Gem\_e2](https://community.electricforum.com/u/Gem_e2)\
**Post date:** [February 15, 2017, 3:46pm UTC](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054/20 "2017-02-15T15:46:02Z")

</div>

OK if you have a Curtis controller its a Series motor on that cart ?  
can you see a name on controller,curtis 1204 ?  
think you have a big main relay and also a big relay for forward,reverse  
you need to reed the voltage at this relays and on controller pin 1  
release the parkbrake and put on throttle  
also disconnect charger for interlock  
do you here beeper on reverse ?

[Next page](https://community.electricforum.com/t/48v-trans-2-battery-installation/12054.md?page=2)
