# 2006 E4 won't run, code 81 - please read

**URL:** <https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392>\
**Category:** GEM Forum\
**Created:** [May 18, 2023, 7:44pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392 "2023-05-18T19:44:20Z")\
**Posts on this page:** 17\
**Page:** 1

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [May 18, 2023, 7:44pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/1 "2023-05-18T19:44:20Z")

</div>

I have replaced speed sensor and magnet. I have had the throttle checked out, it’s fine. I have had the controller rebuilt and updated. I am right where I started. Step on gas, solenoid clicks, code 81 and wrench displays. Turn off key and one sec later get a one second beep.

I am out of ideas. Please help.

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [May 18, 2023, 7:56pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/2 "2023-05-18T19:56:30Z")

</div>

As you can see, shot-gunning parts rarely helps.

Disconnect sensor and meter, to test connections.  
Black to red ~12v  
Black to green Some +volts over 3.2v. (memory fails)

Connect sensor, meter from black to green. (pin wires)  
While very slowly rolling car or turning wheels, voltage will drop to near zero 48 times per rotation.  
Count not important, looking for steady pulses from high to low.

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [May 18, 2023, 7:58pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/3 "2023-05-18T19:58:16Z")

</div>

Well, The magnet was cracked. The controller tested bad… But I’m still were I started. Will test voltage tonight.

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [May 18, 2023, 8:03pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/4 "2023-05-18T20:03:23Z")

</div>

On the right track then. Maybe the ne magnet/sensor was bad.

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [May 18, 2023, 8:08pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/5 "2023-05-18T20:08:17Z")

</div>

Depending on where you got that new speed sensor- I see some chatter about the cheap ones from Amazon are not working.  
I don’t know why.  
Stay away from Gas Station Sushi.

Try your old sensor. Was it also giving you the -81?  
How did you determine the controller was bad?  
What made you think this was a pedal issue?

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [May 18, 2023, 8:32pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/6 "2023-05-18T20:32:26Z")

</div>

Ride-4-Fun sensor. Old one started this process, died in pouring rain, towed home. Got 81 code and nothing but solenoid click. Found crack in magnet, replaced both. Same result. Sent in controller and pedal to R4F and they said pedal good, controller bad. Seemed very likely. Back to square one.

---

<div class="post-metadata">

**Author:** ![AssyRequired](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/assyrequired/32/7621_2.png) [@AssyRequired](https://community.electricforum.com/u/AssyRequired)\
**Post date:** [May 18, 2023, 8:44pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/7 "2023-05-18T20:44:08Z")

</div>

A crack in the magnet will not throw a code -81 and kill the car.  
The sensors are all sealed up and not likely the cause.  
I would have looked at water getting in somewhere like the top of the controller. or controller plug.

Pedal would have thrown it’s own array of codes, but not -81.  
It wouldn’t be the first time something came back from R4F still not repaired.

Check your voltages at the sensor plug like how Inwo suggested above ^^^.  
What does it do without the sensor plugged in?

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [May 18, 2023, 9:44pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/8 "2023-05-18T21:44:53Z")

</div>

Plug was dry. Crack was discovered after replacement. Is there a way to test the motor?

---

<div class="post-metadata">

**Author:** ![Inwo](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/inwo/32/1067_2.png) [@Inwo](https://community.electricforum.com/u/Inwo)\
**Post date:** [May 18, 2023, 11:03pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/9 "2023-05-18T23:03:38Z")

</div>

> [@Thunderbox](#):
>
> there a way to test the motor?

Motor could be bad. Never thought of that.  
Does motor turn at all before fault?

You can ohm it out, which will show a major fault.  
Or jack up the car and test motor at 12v with jumper cables.

That would explain it all. Nothing wrong with controller or other parts. Stuck brushes or such.

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [July 25, 2023, 8:41pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/10 "2023-07-25T20:41:59Z")

</div>

It was a bad motor btw.

---

<div class="post-metadata">

**Author:** ![RichardE](https://avatars.discourse-cdn.com/v4/letter/r/7c8e57/32.png) [@RichardE](https://community.electricforum.com/u/RichardE)\
**Post date:** [July 26, 2023, 3:54pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/11 "2023-07-26T15:54:59Z")

</div>

Are you able to describe the exact fault with the motor and the test that revealed its faultiness?

Context: I have a 2014 Gem e2 that is exhibiting error 81 (along with error 45 in some cases) and am looking to tap into the accumulated wisdom of the forum.  
[Rather than hijack someone else’s thread, I’d like to post my own question, but as a newbie, I cannot see a way to do so. How do I do that? FAQ/Guidelines didn’t help.]

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [July 26, 2023, 4:20pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/12 "2023-07-26T16:20:15Z")

</div>

It was fried. Pretty obvious when I took the covers off the motor.

 ![IMG_5123](https://canada1.discourse-cdn.com/flex030/uploads/electricforum/original/2X/1/1436e88d7a0102e9c79dc6273a824c67df2c121b.jpeg)

---

<div class="post-metadata">

**Author:** ![RichardE](https://avatars.discourse-cdn.com/v4/letter/r/7c8e57/32.png) [@RichardE](https://community.electricforum.com/u/RichardE)\
**Post date:** [July 26, 2023, 4:25pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/13 "2023-07-26T16:25:07Z")

</div>

Ok thanks. I will remove the cover and take a look.

---

<div class="post-metadata">

**Author:** ![LithiumGods](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/lithiumgods/32/672_2.png) [@LithiumGods](https://community.electricforum.com/u/LithiumGods)\
**Post date:** [July 29, 2023, 1:38pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/14 "2023-07-29T13:38:30Z")

</div>

did you repair motor?

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [September 14, 2023, 11:28pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/15 "2023-09-14T23:28:48Z")

</div>

Bought new from D&D…

---

<div class="post-metadata">

**Author:** ![dougl](https://avatars.discourse-cdn.com/v4/letter/d/b19c9b/32.png) [@dougl](https://community.electricforum.com/u/dougl)\
**Post date:** [September 15, 2023, 12:05am UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/16 "2023-09-15T00:05:14Z")

</div>

FYI, at one point Rodney( oldhouseboater ) was looking for core motors…

> [@Motors for sale](https://community.electricforum.com/t/motors-for-sale/24272):
>
> RODNEY motors serviced, tested, ready to go. $200 up. What are you looking for. [rodneyadiehl@aol.com](mailto:rodneyadiehl@aol.com)

---

<div class="post-metadata">

**Author:** ![Thunderbox](https://avatars.discourse-cdn.com/v4/letter/t/4da419/32.png) [@Thunderbox](https://community.electricforum.com/u/Thunderbox)\
**Post date:** [September 15, 2023, 7:56pm UTC](https://community.electricforum.com/t/2006-e4-wont-run-code-81-please-read/26392/17 "2023-09-15T19:56:07Z")

</div>

Bummer. I left it at an electric motor/generator place locally to recycle.
