# 00 e825 runs but looses power and stops

**URL:** <https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691>\
**Category:** GEM Forum\
**Created:** [July 25, 2019, 6:04pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691 "2019-07-25T18:04:05Z")\
**Posts on this page:** 14\
**Page:** 1

<div class="post-metadata">

**Author:** ![metalman](https://avatars.discourse-cdn.com/v4/letter/m/6de8d8/32.png) [@metalman](https://community.electricforum.com/u/metalman)\
**Post date:** [July 25, 2019, 6:04pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/1 "2019-07-25T18:04:05Z")

</div>

00 e825 runs but loses power and stops. give “gas” and car starts slow and then shuts down - over an over again??? code 04 and 11 and some times 08. cleaned and tested emg brake switch…good - cleaned and tested accelerator…good?? - swapped out ge 72v-350amp with a spare…same problem!!!

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 15, 2020, 12:57am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/2 "2020-06-15T00:57:58Z")

</div>

I am having a similar issue. my gem car will start go for a bit and then just cut power and then it won’t run again. I have a 2005 Gem e4, batteries are charged getting good voltage. whats strange is that it just randomly started today after I installed a reman’d controller and put in a brand new accelerator pedal (new model). If i disconnect the 23 pin harness I seem to be able to get it to run again (sometimes). no error codes on the dash. I suspect its a wire connected to the 23 pin harness thats shorting out.

---

<div class="post-metadata">

**Author:** ![LithiumGods](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/lithiumgods/32/672_2.png) [@LithiumGods](https://community.electricforum.com/u/LithiumGods)\
**Post date:** [June 15, 2020, 3:02am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/3 "2020-06-15T03:02:10Z")

</div>

Key switch can do it .

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 15, 2020, 3:38am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/4 "2020-06-15T03:38:50Z")

</div>

That seems plausible because I’ve noticed some play in the key when I turn the car on, but if the key switch just dropped the connection wouldn’t the display go out ?

---

<div class="post-metadata">

**Author:** ![LithiumGods](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/lithiumgods/32/672_2.png) [@LithiumGods](https://community.electricforum.com/u/LithiumGods)\
**Post date:** [June 15, 2020, 3:53am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/5 "2020-06-15T03:53:03Z")

</div>

Not necessarily . I have had a few do it .

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 15, 2020, 12:20pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/6 "2020-06-15T12:20:11Z")

</div>

hmm, okay thanks, I’ll look at getting a replacement.

---

<div class="post-metadata">

**Author:** ![LithiumGods](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/lithiumgods/32/672_2.png) [@LithiumGods](https://community.electricforum.com/u/LithiumGods)\
**Post date:** [June 15, 2020, 1:00pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/7 "2020-06-15T13:00:47Z")

</div>

You can pull switch and hotwire to test . I buy replacement from Napa , $15 . There is a thread on here about it

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 16, 2020, 12:59am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/8 "2020-06-16T00:59:05Z")

</div>

I actually just installed the one from NAPA tonight and it seems to have fixed the issue, although I did have to plug in the 23 pin connector to get it started. I did a bunch of test drives and it hasn’t shut off on me yet so fingers crossed. The NAPA key start switch seems alot more solid.

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 17, 2020, 12:55am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/9 "2020-06-17T00:55:16Z")

</div>

welp it was running fine today and then all of a sudden it slowed down I saw smoke coming from the motor and then error 66 came up and then error 51 now I can’t get it to start and its stuck on error 51. when I tried push it it was almost as if the brakes locked up and when I pushed it it was making like a slicing sound. I just had FSIP reman the controller so I really hope its not that.

---

<div class="post-metadata">

**Author:** ![Old\_Houseboater](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/old_houseboater/32/544_2.png) [@Old\_Houseboater](https://community.electricforum.com/u/Old_Houseboater)\
**Post date:** [June 17, 2020, 1:41am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/10 "2020-06-17T01:41:57Z")

</div>

Hmmm

Might I suggest the motor?

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 17, 2020, 1:50am UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/11 "2020-06-17T01:50:06Z")

</div>

Yeah, I’ve replaced everything else. I guess I’ll take it apart and see if the brushes or commutator are worn. I just hope that I didn’t fry the controller in the process.

---

<div class="post-metadata">

**Author:** ![LithiumGods](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/lithiumgods/32/672_2.png) [@LithiumGods](https://community.electricforum.com/u/LithiumGods)\
**Post date:** [June 17, 2020, 2:35pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/12 "2020-06-17T14:35:09Z")

</div>

which motor do you have ?

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [June 17, 2020, 10:16pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/13 "2020-06-17T22:16:35Z")

</div>

I have the stock GE 5HP motor

---

<div class="post-metadata">

**Author:** ![charris2587](https://yyz2.discourse-cdn.com/flex030/user_avatar/community.electricforum.com/charris2587/32/5219_2.png) [@charris2587](https://community.electricforum.com/u/charris2587)\
**Post date:** [July 5, 2020, 9:01pm UTC](https://community.electricforum.com/t/00-e825-runs-but-looses-power-and-stops/16691/14 "2020-07-05T21:01:10Z")

</div>

I just replaced the stock motor with a black advanced GJ04001. It still won’t move. I guess I need to fix the mosfets in the controller then ? It now only seems to throw error 66 when in reverse. When in forward high or low it doesn’t throw any error code
